============================= Install Ceph Object Gateway ============================= The :term:`Ceph Object Gateway` daemon runs on Apache and FastCGI. To run a :term:`Ceph Object Storage` service, you must install Apache and FastCGI. Then, you must install the Ceph Object Gateway daemon. The Ceph Object Gateway supports 100-continue, but you must install Ceph builds of Apache and FastCGI for 100-continue support. To install the Ceph Object Gateway, first install and configure Apache and FastCGI. Then, install the Ceph Object Gateway daemon. If you plan to run a Ceph Object Storage service with a federated architecture (multiple regions and zones), you must also install the synchronization agent. See `Get Packages`_ for information on adding Ceph packages to each Ceph Node. Ensure that you have executed those steps on each Ceph Node first. Apache/FastCGI w/out 100-Continue ================================= You may use standard Apache and FastCGI packages for your Ceph Object Gateways. However, they will not provide 100-continue support. Debian Packages --------------- To install Apache and FastCGI Debian packages, execute the following:: sudo apt-get install apache2 libapache2-mod-fastcgi RPM Packages ------------ To install Apache and FastCGI RPMs, execute the following:: rpm -ivh fcgi-2.4.0-10.el6.x86_64.rpm rpm -ivh mod_fastcgi-2.4.6-2.el6.rf.x86_64.rpm Or:: sudo yum install httpd mod_fastcgi Apache/FastCGI w/ 100-Continue ============================== The Ceph community provides a slightly optimized version of the ``apache2`` and ``fastcgi`` packages. The material difference is that the Ceph packages are optimized for the ``100-continue`` HTTP response, where the server determines if it will accept the request by first evaluating the request header. See `RFC 2616, Section 8`_ for details on ``100-continue``. You can find the most recent builds of Apache and FastCGI packages modified for Ceph at `gitbuilder.ceph.com`_. Debian Packages --------------- #. Add a ``ceph-apache.list`` file to your APT sources. :: echo deb http://gitbuilder.ceph.com/apache2-deb-$(lsb_release -sc)-x86_64-basic/ref/master $(lsb_release -sc) main | sudo tee /etc/apt/sources.list.d/ceph-apache.list #. Add a ``ceph-fastcgi.list`` file to your APT sources. :: echo deb http://gitbuilder.ceph.com/libapache-mod-fastcgi-deb-$(lsb_release -sc)-x86_64-basic/ref/master $(lsb_release -sc) main | sudo tee /etc/apt/sources.list.d/ceph-fastcgi.list #. Update your repository and install Apache and FastCGI:: sudo apt-get update && sudo apt-get install apache2 libapache2-mod-fastcgi RPM Packages ------------ To install Apache with 100-continue, execute the following steps: #. Install ``yum-plugin-priorities``. :: sudo yum install yum-plugin-priorities #. Ensure ``/etc/yum/pluginconf.d/priorities.conf`` exists. #. Ensure ``priorities.conf`` enables the plugin. :: [main] enabled = 1 #. Add a ``ceph-apache.repo`` file to ``/etc/yum.repos.d``. Replace ``{distro}`` with the name of your distribution (e.g., ``centos6``, ``rhel6``, etc.) :: [apache2-ceph-noarch] name=Apache noarch packages for Ceph baseurl=http://gitbuilder.ceph.com/apache2-rpm-{distro}-x86_64-basic/ref/master enabled=1 priority=2 gpgcheck=1 type=rpm-md gpgkey=https://ceph.com/git/?p=ceph.git;a=blob_plain;f=keys/autobuild.asc [apache2-ceph-source] name=Apache source packages for Ceph baseurl=http://gitbuilder.ceph.com/apache2-rpm-{distro}-x86_64-basic/ref/master enabled=0 priority=2 gpgcheck=1 type=rpm-md gpgkey=https://ceph.com/git/?p=ceph.git;a=blob_plain;f=keys/autobuild.asc #. Add a ``ceph-fastcgi.repo`` file to ``/etc/yum.repos.d``. Replace ``{distro}`` with the name of your distribution (e.g., ``centos6``, ``rhel6``, etc.) :: [fastcgi-ceph-basearch] name=FastCGI basearch packages for Ceph baseurl=http://gitbuilder.ceph.com/mod_fastcgi-rpm-{distro}-x86_64-basic/ref/master enabled=1 priority=2 gpgcheck=1 type=rpm-md gpgkey=https://ceph.com/git/?p=ceph.git;a=blob_plain;f=keys/autobuild.asc [fastcgi-ceph-noarch] name=FastCGI noarch packages for Ceph baseurl=http://gitbuilder.ceph.com/mod_fastcgi-rpm-{distro}-x86_64-basic/ref/master enabled=1 priority=2 gpgcheck=1 type=rpm-md gpgkey=https://ceph.com/git/?p=ceph.git;a=blob_plain;f=keys/autobuild.asc [fastcgi-ceph-source] name=FastCGI source packages for Ceph baseurl=http://gitbuilder.ceph.com/mod_fastcgi-rpm-{distro}-x86_64-basic/ref/master enabled=0 priority=2 gpgcheck=1 type=rpm-md gpgkey=https://ceph.com/git/?p=ceph.git;a=blob_plain;f=keys/autobuild.asc #. Update your repo and install Apache and FastCGI. :: sudo yum update && sudo yum install httpd mod_fastcgi Configure Apache/FastCGI ======================== To complete the installation, ensure that you have the rewrite module enabled and FastCGI enabled. The steps differ slightly based upon the type of package installation. Debian-based Packages --------------------- #. Open the ``apache2.conf`` file. :: sudo vim /etc/apache2/apache2.conf #. Add a line for the ``ServerName`` in the Apache configuration file. Provide the fully qualified domain name of the server machine (e.g., ``hostname -f``). :: ServerName {fqdn} #. Enable the URL rewrite modules for Apache and FastCGI. :: sudo a2enmod rewrite sudo a2enmod fastcgi #. Restart Apache so that the foregoing changes take effect. :: sudo service apache2 restart RPM-based Packages ------------------ #. Open the ``httpd.conf`` file. :: sudo vim /etc/httpd/conf/httpd.conf #. Uncomment ``#ServerName`` and add the name of your server. Provide the fully qualified domain name of the server machine (e.g., ``hostname -f``).:: ServerName {fgdn} #. Ensure that the Rewrite module is enabled. :: #if not present, add: LoadModule rewrite_module modules/mod_rewrite.so #. Save the ``httpd.conf`` file. #. Ensure that the FastCGI module is enabled. The installer should include an ``/etc/httpd/conf.d/fastcgi.conf`` file that loads the FastCGI module. :: #if not present, add: LoadModule fastcgi_module modules/mod_fastcgi.so #. Restart Apache so that the foregoing changes take effect.. :: /etc/init.d/httpd restart .. _RFC 2616, Section 8: http://www.w3.org/Protocols/rfc2616/rfc2616-sec8.html .. _gitbuilder.ceph.com: http://gitbuilder.ceph.com .. _Installing YUM Priorities: ../yum-priorities Enable SSL ========== Some REST clients use HTTPS by default. So you should consider enabling SSL for Apache. Use the following procedures to enable SSL. .. note:: You can use self-certified certificates. Some client APIs check for a trusted certificate authority. You may need to obtain a SSL certificate from a trusted authority to use those client APIs. Debian Packages --------------- To enable SSL for Debian/Ubuntu systems, execute the following steps: #. Ensure that you have installed the dependencies. :: sudo apt-get install openssl ssl-cert #. Enable the SSL module. :: sudo a2enmod ssl #. Generate a certificate. :: sudo mkdir /etc/apache2/ssl sudo openssl req -x509 -nodes -days 365 -newkey rsa:2048 -keyout /etc/apache2/ssl/apache.key -out /etc/apache2/ssl/apache.crt #. Restart Apache. :: service apache2 restart See the `Ubuntu Server Guide`_ for additional details. RPM Packages ------------ To enable SSL for RPM-based systems, execute the following steps: #. Ensure that you have installed the dependencies. :: sudo yum install mod_ssl openssl #. Ensure the SSL module is enabled. #. Generate a certificate and copy it the appropriate locations. :: openssl x509 -req -days 365 -in ca.csr -signkey ca.key -out ca.crt cp ca.crt /etc/pki/tls/certs cp ca.key /etc/pki/tls/private/ca.key cp ca.csr /etc/pki/tls/private/ca.csr #. Restart Apache. :: /etc/init.d/httpd restart See `Setting up an SSL secured Webserver with CentOS`_ for additional details. Add Wildcard to DNS =================== To use Ceph with S3-style subdomains (e.g., ``bucket-name.domain-name.com``), you need to add a wildcard to the DNS record of the DNS server you use with the ``radosgw`` daemon. .. tip:: The address of the DNS must also be specified in the Ceph configuration file with the ``rgw dns name = {hostname}`` setting. For ``dnsmasq``, consider addding the following ``address`` setting with a dot (.) prepended to the host name:: address=/.{hostname-or-fqdn}/{host-ip-address} address=/.ceph-node/192.168.0.1 For ``bind``, consider adding the a wildcard to the DNS record:: $TTL 604800 @ IN SOA ceph-node. root.ceph-node. ( 2 ; Serial 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL ; @ IN NS ceph-node. @ IN A 192.168.122.113 * IN CNAME @ Restart your DNS server and ping your server with a subdomain to ensure that your Ceph Object Store ``radosgw`` daemon can process the subdomain requests. :: ping mybucket.{fqdn} ping mybucket.ceph-node Install Ceph Object Gateway =========================== Ceph Object Storage services use the Ceph Object Gateway daemon (``radosgw``) to enable the gateway. For federated architectures, the synchronization agent (``radosgw-agent``) provides data and metadata synchronization between zones and regions. Debian Packages --------------- To install the Ceph Object Gateway daemon, execute the following:: sudo apt-get install radosgw To install the Ceph Object Gateway synchronization agent, execute the following:: sudo apt-get install radosgw-agent RPM Packages ------------ To install the Ceph Object Gateway daemon, execute the following:: yum install ceph-radosgw ceph To install the Ceph Object Gateway synchronization agent, execute the following:: yum install radosgw-agent .. _Get Packages: ../get-packages .. _Ubuntu Server Guide: https://help.ubuntu.com/12.04/serverguide/httpd.html .. _Setting up an SSL secured Webserver with CentOS: http://wiki.centos.org/HowTos/Https