Allows arrangement of multiple windows such as:
ffmpeg -re -f lavfi -i mandelbrot -f sdl -window_x 1 -window_y 1 mandelbrot -vf waveform,format=yuv420p -f sdl -window_x 641 -window_y 1 waveform -vf vectorscope,format=yuv420p -f sdl -window_x 1 -window_y 481 vectorscop
Some changes by Marton Balint:
- allow negative position (partially or fully out-of-screen positions seem to
be sanitized automatically by SDL (or my WM?), so no special handling is
needed)
- only show window after the position is set
- do not use resizable and borderless flags at the same time, that caused
issues in ffplay
- add docs
Signed-off-by: Marton Balint <cus@passwd.hu>
The existing av_mediacodec_release_buffer allows the user to render
or discard the Surface-backed frame. This new method allows the user
to control exactly when the frame will be rendered to its SurfaceView.
Available since Android API 21.
Signed-off-by: Aman Gupta <aman@tmm1.net>
This allows switching between absolute (LUFS) and relativ (LU) display
in the status line.
Signed-off-by: Daniel Molkentin <daniel@molkentin.de>
Signed-off-by: Conrad Zelck <c.zelck@imail.de>
This eases meeting the target level during live mixing.
Signed-off-by: Daniel Molkentin <daniel@molkentin.de>
Signed-off-by: Conrad Zelck <c.zelck@imail.de>
Allow to show short-term instead of momentary in gauge. Useful for monitoring
whilst live mixing.
Signed-off-by: Daniel Molkentin <daniel@molkentin.de>
Signed-off-by: Conrad Zelck <c.zelck@imail.de>
This allows getting data only from a specific source IP. This is useful not
only for unicast but for multicast as well because multicast source
subscriptions do not act as source filters for the incoming packets.
Signed-off-by: Marton Balint <cus@passwd.hu>
This option is useful for maintaining input synchronization across N
different hardware devices deployed for 'N-way' redundancy.
The system time of different hardware devices should be synchronized
with protocols such as NTP or PTP, before using this option.
Signed-off-by: Marton Balint <cus@passwd.hu>
Also bump the API version requirement to 10.9.5, because on olders versions
there were some reports of crashes using the undocumented, yet available
BMDDeckLinkDeviceHandle.
Signed-off-by: Marton Balint <cus@passwd.hu>
Sets the level based on the stream properties if it is not explicitly
set by the user. Also add a tier option to set general_tier_flag, since
that affects the level choice.
This was added in libva 2.1.0 (VAAPI 1.1.0). Use AVCodecContext.qmax,
matching the existing behaviour for qmin, and clean up the defaults so
that we only pass min/max when explicitly set.
Query which modes are supported and select between VBR and CBR based
on that - this removes all of the codec-specific rate control mode
selection code.
Previously there was one fixed choice for each codec (e.g. H.265 -> Main
profile), and using anything else then required an explicit option from
the user. This changes to selecting the profile based on the input format
and the set of profiles actually supported by the driver (e.g. P010 input
will choose Main 10 profile for H.265 if the driver supports it).
The entrypoint and render target format are also chosen dynamically in the
same way, removing those explicit selections from the per-codec code.
Dave Rice
Paul B Mahol
Martin Vignali
Mark Thompson
Aman Gupta
Daniel Molkentin
Marton Balint
Karthick Jeyapal
Michael Niedermayer
Sergey Lavrushkin
hwren